Mindray BeneFusion SP3 Service Manual Download

Page: 36 / 80

3-12

3. Use a soft cloth. After absorbing an appropriate amount of cleaning agent, wipe

the surface of the equipment.

4. If necessary, wipe off excess cleaning agent with a dry cloth.

5. Air dry the equipment in a cool, ventilated environment.

3.7.2 Disinfection

Disinfection operations may cause some damage to the syringe pump. Disinfection

is recommended to be performed only if it is deemed necessary in your intended

maintenance plan. Clean the equipment before disinfection.

Recommended disinfectants are: ethanol (70%), isopropanol (70%), 2%

glutaraldehyde solution.

CAUTION



Do not use gas (EtO) or formaldehyde for disinfection.



The syringe pump and its accessories must not be sterilized by high

pressure or high temperature.

Summary of Contents for BeneFusion SP3

















































































Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands

Mindray BeneFusion SP3, Service Manual

Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands