Mindray BeneFusion SP3 Service Manual Download

Page: 71 / 80

7-1

Upgrade

7.1 Tools

During upgrade, you may use the following tools:



Multi-function serial cable



PC burning tool software

7.2 Software Upgrade

This syringe pump can be upgraded by software that runs directly on a desktop PC

or mobile PC. Through the multi-function port, you can connect the syringe pump

with a PC to upgrade the software and brand library. (Note: the follow-up brand

library will be packaged with the whole software, and you can upgrade the whole

software and the brand library by upgrading the software package).

7.2.1 Software Burning Method

1. Plug the multi-function serial cable into the multi-function port on the main unit

as shown.

2. The other end of the multi-function serial cable is the standard BD9 serial port.

Connect the end to the computer as shown.

Summary of Contents for BeneFusion SP3

















































































Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands

Mindray BeneFusion SP3, Service Manual

Search results

Summary of Contents for BeneFusion SP3

Reviews:

Related manuals for BeneFusion SP3

Brands by name

Popular brands