MIMAKI SWJ-320 S2, Maintenance Manual

Page: 186 / 210

© 2013 MIMAKI ENGINEERING CO.,LTD. 7.1.2 P.3
7.1.2 List of Error Messages
R.1.2
1
2
3
4
5
6
7
8
29
ERROR 19d
HDC V36 [12__]
Control error to HDC PCB voltage
Voltage of the HDC PCB that displayed
number on the LCD is lower than pre-
scribed voltage. 1. Check the output pressure of the DC power supply (36V)
and the DC power supply (5V).
2. Replace the HDC PCB with a new one.
3. Replace the power supply above.
4. Replace the MAIN PCB with a new one.
( Refer to 3.3.1)
30
ERROR 1a1
INK SUP PMP [12__]
Voltage of the ink supply pump can not be
set it to the prescribed voltage.
1. Check if there is no parameter error?
2. Check the output pressure of the DC power supply (36V)
and the DC power supply (5V).
3. Replace the power supply above.
4. Replace the CIO PCB with a new one.
5. Replace the MAIN PCB with a new one.
( Refer to 3.3.1)
31
ERROR 201
COMMAND
Command error
Other data than commands is received 1. Check if the output set of the PC matches the set of the
machine side?
2. Change the profile.
3. Check if there is no parameter error?
4. Check if there is no trouble on the USB Cable?
5. Replace the USB Cable.
6. Replace the MAIN PCB with a new one.
( Refer to 3.3.1)
32
ERROR 202
PARAMETER
Parameter error
Parameter out of the numeral value range
is received
33
ERROR 304
USB INIT ERR
USB initialization error
(Failures in initializing USB device) 1. Check if there is no parameter error?
2. Replace the USB Cable.
3. Replace the MAIN PCB with a new one.
( Refer to 3.3.1)
34
ERROR 305
USB TIME OUT
USB time-out
(Occurrence of time-out error on USB
device)
35
ERROR 401
MOTOR X
X Servo error
(Excessive load to the X-motor) 1. Check if there is no error on the print data.
(Check if the same error occurs on other data?)
2. Check if there is no trouble on the Timing Belt.
3. Check if there is no trouble on the Motor Cable.
(disconnecting, burnout, or the like)
4. Check the FFC between each PCB and Short-connectors
connected on the PCB.
5. Replace the X-axis Motor with a new one. ( Refer to 3.3.1)
36
ERROR 403
X CURRENT
X-motor current
(Over current error of X-motor is detected.)
37
ERROR 402
MOTOR Y
Y Servo error
(Excessive load to the Y-motor) 1. Check if there is no error on the print data.
(Check if the same error occurs on other data?)
2. Check if it moves to the Y-direction smoothly in the power-
off condition.
3. Check if there is no trouble on the Timing Belt.
4. Check if there is no trouble on the Motor Cable.
(disconnecting, burnout, or the like)
5. Check the FFC between each PCB and Short-connectors
connected on the PCB.
6. Replace the Y-axis motor with a new one. ( Refer to 6.3.2)
38
ERROR 404
Y CURRENT
Y-motor current
(Over current error of Y-motor is detected.)
 List of Error Messages ?3/5?
No. LCD Cause List of Countermeasures
MAINTENANCE MANUAL > Troubleshooting > Details on Errors and Malfunctions > List of Error Messages
Model SWJ-320S Issued 2012.07.19 Revised 2013.03.08 F/W ver 1.0 Remark
1.2
Rev.