Milnor E-P Plus Reference Download Page 90

Page: 90 / 92

Pellerin Milnor Corporation

Figure 16.

Wiring Diagram for Cable to Connect a Machine to a Serial Memory Storage Device

Receptacle

Legend

A...

Receptacle on machine (with male pins). Pin functions are as follows:

1&2

=Se-

rial low. This application only uses Pin 1;

3&4

=Serial high. This application

only uses Pin 3;

6&9

=Ground. This application only uses Pin 9;

5&7

=Not used

in this application;

=+5VDC. Provides power to memory storage device.

B...

Plug on cable (with female pin sockets)

C...

Memory storage device (front panel may be different)

D...

Tie shield on this end of cable to ground. Leave unconnected on other end.

Plug and Storage Device

BNCUUI01 / 2018303

BNCUUI01

0000196633

A.6

1/2/20 1:30 PM

Released

5.4

Printer Requirements and Settings

BNCUUI01.C01 0000196632 C.2 A.6 1/2/20 1:30 PM Released

NOTICE:

Because of the many differences among printer makes and models, Milnor

cannot ensure suitability or troubleshoot printers other than those described in this docu-
ment (or certain older approved models), with the required interface cable.

5.4.1

Cable Requirements

BNCUUI01.R01 0000196631 C.2 A.6 1/2/20 1:30 PM Released

The printer must be connected to the printer port on the machine using the appropriate one of the
following Milnor interface cables:

Table 17.

Milnor Printer Cables

Printer Cable Part Number

Description

10YMK2PNTR

100-formula washer-extractor, dryer, extractor, and Miltron
(CBW

) controllers

10YCBWPNTR

Non-serial Miltron (CBW) controller

08MPSERCBL

Mentor

(CBW) and Mildata

controllers

Supplemental Information

Summary of Contents for E-P Plus





























































































Search results

Summary of Contents for E-P Plus

Reviews:

Milnor E-P Plus, Reference, Page: 90 / 92

Search results

Summary of Contents for E-P Plus

Reviews: