manualshive.com logo in svg

Milnor E-P Plus, Reference, Page: 70 / 92

Share
Download
Milnor E-P Plus Reference Download Page 70

64

Pellerin Milnor Corporation

4.1.4

Actuating Microprocessor Outputs

BNCJHT01.R05 0000190746 C.2 F.3 B.3 1/2/20 1:16 PM Released

Machine functions may be tested individually or in groups by using the

Test Outputs

component

of the

Manual menu

. The machine must be idle (not running a formula).

DANGER:

Crushing and Entanglement Hazard —

Bare manual outputs actuate

washer-extractor mechanisms. Keep all personnel clear.

Display or Action

Explanation

Accesses the

Manual menu

.

MANUAL MENU

3

TEST OUTPUTS

This is the

Manual menu

display with the

Test Outputs

compo-

nent selected.
Accesses the output testing selection.

TEST OUTPUTS

01

INJECT CHEMICAL 5

This is the

Output testing

display.

Indexes forward and backward through the output names, as
shown in the table of outputs in this section.

TEST OUTPUTS

07

COLD WATER VALVE

Example display with output in place to be selected and subse-
quently actuated.

Accesses the selected output for actuation. All outputs are initially
disabled when accessed.

COLD WATER VALVE
0=OFF

1=ON

0

Example display with output accessed and disabled.

Enables the output (turns the output on).

COLD WATER VALVE
0=OFF

1=ON

1

Example display with output enabled. The cold water valve is
open.

If the output was already on, this keystroke turns it off.

COLD WATER VALVE
0=OFF

1=ON

0

Example display with output disabled. The cold water valve is
closed.
Disables (turns off) the output if it was previously enabled, and
advances to the next output.

HOT WATER VALVE
0=OFF

1=ON

0

Display after pressing

to advance to the next output.

Disables the output if it was enabled, then returns to the

Run

mode

.

RUN FORMULA

00

OK TO POWER OFF

Display of

Run mode.

Troubleshooting

Summary of Contents for E-P Plus





























































































Reviews:

No comments