Milnor E-P Plus Reference Download Page 46 | Manualshive

Page: 46 / 92

Milnor E-P Plus Reference Download Page 46

40

Pellerin Milnor Corporation

Display or Action

Explanation

RUN KEY TURNED EARLY
ALL NEW CHANGES LOST

This message appears on later software versions only. It indicates

that the key was turned to

before

was pressed.

Returns the controller to the

Program menu.

PROGRAM

0

MENU

OK TURN KEY TO RUN

This is the

Program menu

, from which the operator can correctly

save the modified formulas.

,

Saves all formula modifications and returns the controller to the

Run mode

.

PLEASE WAIT

This display indicates that the formula modifications are being
saved in permanent memory.

RUN FORMULA

00

OK TO POWER OFF

This is the

Run Formula

display.

2.3.3.6.8

How to Save or Discard Changes

BNCJUP03.C20 0000192000 C.2 D.2 A.8 1/2/20 1:16 PM Released

Use the procedures detailed above to navigate in a formula and make changes. The following pro-
cedures should be used to return to the formula menu and either save or discard the changes
made.

Display or Action

Explanation

Saves all changes if the cursor is on the

Step Number

. This key

may need to be pressed more than one time to exit the formula.

Exits the formula and discards all changes made during this pro-
gramming session.

2.3.4

Configure the Control (Option 2)

BNCJUP04.C01 0000192159 C.2 D.2 B.3 1/2/20 1:16 PM Released

Because the microprocessor control system used in this machine is capable of controlling several
different models with a wide variety of options, each unit must be configured to match its specific
model and type of washer-extractor. This configuration informs the microprocessor of the charac-
teristics of this machine, such as the number of water valves, the presence of temperature control,
cooldown, etc. Such decisions are discrete to the specific machine and must never be changed un-
less options are later added or removed. In addition to these hardware-specific decisions, certain
configuration choices, such as the display of English or metric units, are left to the discretion of
the owner/operator.

TIP:

The Milnor

®

E-P Plus

®

Programmer software for Microsoft Windows allows the

user to configure the machine and program formulas on a personal computer, then down-
load the data to each machine through a special cable (Milnor part number
KXMDSWBRS1). With the E-P Plus Programmer, descriptive names for each formula
can be created and downloaded. When a machine is configured by using the front panel
controls instead of the programmer software, all descriptive formula names will be re-
placed with “Formula XX,” where XX is the formula number.

«
...
44
45
46
47
48
...
»

Summary of Contents for E-P Plus





























































































Reviews:

No comments