manualshive.com logo in svg

Milnor E-P Plus, Reference, Page: 30 / 92

Share
Download
Milnor E-P Plus Reference Download Page 30

24

Pellerin Milnor Corporation

Moves the cursor backward among the two pages, through each
valid decision within a specific step, except in the following
cases:

•

If the cursor is at decision

T

on

Page A

, it will move to the

step number.

•

If the cursor is at the first decision on

Page B

, it will back up

to the first valid decision (

C

) for the first chemical com-

manded in this bath.

Displays the name of the formula and step being modified.

2.3.3.4

Create a New Formula

BNCJUP03.C07 0000191941 C.2 D.2 B.3 1/2/20 1:16 PM Released

Creating a new formula with the E-P Plus controller entails adding and defining steps using one
of the existing but blank formula numbers.

Display or Action

Explanation

PROGRAM

1

MENU

ADD/CHANGE FORMULA

This is

Option 1

of the

Program

menu. From this display, either

access a formula by number to change or create, or select another
available menu option.

Accesses the formula list for selection of a formula number to
change or create.

ADD/CHANGE FORMULA

00

RETURN TO MENU

This is the

Add/Change Formula

display. From this display, ei-

ther back up to the

Program

menu, or begin creating or changing

a formula.
Scrolls the available formula numbers. These keystrokes select a
formula for adding if the formula number hasn't already been pro-
grammed. The number is selected for

change

if it has already

been programmed.

ADD

/CHANGE FORMULA

23

FORMULA NUMBER 23

Formula 23 is available for

adding

because it does not currently

exist.

ADD/

CHANGE

FORMULA

07

FORMULA NUMBER 07

Formula 07 is available for

changing

because it already exists.

Accesses the selected formula for programming. Valid formula
numbers are 01 through 30.

07 TMMQFFFHC LSCWSS*

01

205012523 200----

Formula 07, Step 01 selected for programming. Refer to

2.3.3.6.2:

The Step Decisions, page 26

for detailed programming

instructions.

2.3.3.5

Delete an Existing Formula

BNCJUP03.C08 0000191940 C.2 D.2 A.8 1/2/20 1:16 PM Released

Display or Action

Explanation

03 TMMQFFFHC LSCWSS*
01

0

000------ ------

Delete an existing formula by making step 01 an

End

step. Ac-

complish this by setting the

T

value for step 01 of the formula to

0.

Programming

Summary of Contents for E-P Plus





























































































Reviews:

No comments