manualshive.com logo in svg

Milnor E-P Plus, Reference, Page: 79 / 92

Share
Download
Milnor E-P Plus Reference Download Page 79

Pellerin Milnor Corporation

73

1. Reconfigure the machine according to the configuration infor-

mation in

2.3: Programming the E-P Plus

®

Controller, page 20

.

2. Reinstall the standard (default) formulas according to the de-

fault formula loading procedure in

2.3: Programming the E-P

Plus

®

Controller, page 20

3. Reprogram any lost wash formulas according to

2.3: Program-

ming the E-P Plus

®

Controller, page 20

.

MEMORY: FLASH IS NOT

This message appears when the microprocessor cannot read from
the flash memory.

TALKING

1. Lock off and tag out power to the machine.

2. Replace flash memory. Contact the Milnor

®

factory to ensure

that the replacement memory is the most current version for
your machine.

3. Restore power to machine.

4. Reconfigure the machine according to the configuration infor-

mation in

2.3: Programming the E-P Plus

®

Controller, page 20

.

5. Reinstall the standard (default) formulas according to the de-

fault formula loading procedure in

2.3: Programming the E-P

Plus

®

Controller, page 20

.

6. Reprogram lost wash formulas according to

2.3: Programming

the E-P Plus

®

Controller, page 20

A/D BOARD IS

This error message indicates that the analog to digital board is not
communicating with the microprocessor.

NOT TALKING

1. Lock off and tag out power to the machine.

2. Check the connections at both ends of the ribbon cable be-

tween the processor board and the analog to digital board.

3. Restore power.

4. If the error persists, lock off and tag out power to the machine.

Have a qualified service technician replace the suspect board.

4.2.2

Error Messages during Normal Operation

BNCJHT02.R01 0000192187 C.2 B.3 1/2/20 1:16 PM Released

If an error message appears on the bottom line of the display while the machine is running, the
timer shown on the top line will stop counting. When the error is corrected, the timer resumes

Troubleshooting

Summary of Contents for E-P Plus





























































































Reviews:

No comments