manualshive.com logo in svg

Milnor E-P Plus, Reference, Page: 68 / 92

Share
Download
Milnor E-P Plus Reference Download Page 68

62

Pellerin Milnor Corporation

Accesses the

Manual menu.

MANUAL MENU

Reverse type indicates blinking cursor position. Select one of the

Manual menu

modes or return to the

Run mode

, as described

below.

1

SOFTWARE DATE CODE

Scrolls forward/backward through the available modes of the

Manual menu.

Returns to the

Run mode.

RUN FORMULA

Run mode

selected; control is awaiting selection of a valid for-

mula number. The formula number that was selected when the

Manual menu

was accessed appears on the display.

00

OK TO POWER OFF

4.1.1.3

How to Return to the Run Mode from the Manual Menu

BNCJHT01.R02 0000190749 C.2 F.3 A.9 1/2/20 1:16 PM Released

Display or Action

Explanation

Enters the

Manual menu

from

Run mode

.

MANUAL MENU

This is the

Manual menu

display.

1

SOFTWARE DATE CODE

Exits the

Manual menu

to the

Run mode

.

RUN FORMULA

This is the

Run mode

display. Select a formula to run, or turn off

machine power.

00

OK TO POWER OFF

4.1.2

Determining the Software Version

BNCJHT01.R03 0000190748 C.2 F.3 B.3 1/2/20 1:16 PM Released

Display or Action

Explanation

Accesses the

Manual menu

.

MANUAL MENU

1

SOFTWARE DATE CODE

Manual menu

accessed and

Software date code mode

selected.

Hold both buttons depressed to view the software date code and
machine configuration information, as shown below.

EP-PLUS/H7J 97005
RESTAURANTS LAUNDRY

Machine style (H7J), software date code (97005) and configura-
tion (Restaurants Laundry).

RUN FORMULA

xx

FORMULA NUMBER xx

Run mode

display is restored when the

button com-

bination is released.

Troubleshooting

Summary of Contents for E-P Plus





























































































Reviews:

No comments