Milnor E-P Plus Reference Download Page 71

Page: 71 / 92

Pellerin Milnor Corporation

Table 13.

E-P Plus Outputs

Output

Number

Page-

Column

Description

Device

Consequences of Actuation

0–a

Inject chemical 5

Operates inject device for chemical 5

0–b

Inject chemical 1

Operates inject device for chemical 1

0–c

Inject chemical 4

Operates inject device for chemical 4

0–d

Inject chemical 3

Operates inject device for chemical 3

0–e

Inject chemical 2

Operates inject device for chemical 2

0–f

Hot water valve

Opens valve

0–g

Cold water valve

Opens valve

0–h

Drain solenoid

Closes drain

0–i

Flush valve

Opens flush valve

0–j

Cooldown (if equipped)

K10

Operates cooldown valve, if equipped

0–k

Extra water (if

equipped)

K11

Operates extra water valve, if equipped

1–a

Reuse drain (if

equipped)

K12

Operates reuse drain, if equipped

1–b

Steam (if equipped)

K13

Operates steam valve, if equipped

1–c

Inject chemical 6

K14

Operates inject device for chemical 6

1–d

not used

K15

1–e

Door interlock

K16

Energizes door latch to locked position

1–f

Unlock door

K17

Energizes door latch to unlocked position

1–g

Wash clutch

K18

Engages wash clutch

1–h

Extract speed (use only

with empty cylinder)

K19

Locks door, releases brake (if any), and turns
cylinder at extract speed.

1–i

Distribution (drain)

speed (Door must be

closed)

K20

Locks door, releases brake (if any), and turns
cylinder at drain speed.

1–j

Clockwise wash speed

(Door must be closed)

K21

Locks door, releases brake (if any), and turns
cylinder clockwise at wash speed.

1–k

Counter-clockwise wash

speed (Door must be

closed)

K22

Locks door, releases brake (if any), and turns
cylinder counter-clockwise at wash speed.

Buzz signal

Board-mounted

signal

Sounds operator alarm

Run light

Board-mounted

light

Turns on light in Start button (\)

Reversing wash speed

Functional test

Locks door and reverses cylinder at wash
speed.

High Speed extract

Functional test

Locks door and `turns cylinder clockwise at
wash speed, then high extract speed.

Fill to level 1

Functional test

Locks door, closes drain, fills to level 1 with
cold water.

Fill to level 2

Functional test

Locks door, closes drain, fills to level 2 with
cold water.

Troubleshooting

Summary of Contents for E-P Plus





























































































Search results

Summary of Contents for E-P Plus

Reviews:

Milnor E-P Plus, Reference, Page: 71 / 92

Search results

Summary of Contents for E-P Plus

Reviews: