manualshive.com logo in svg

Milnor E-P Plus, Reference, Page: 9 / 92

Share
Download
Milnor E-P Plus Reference Download Page 9

1 Commissioning

BNWCUD03 / 2018256

BNWCUD03

0000189806

A.6

1/2/20 2:19 PM

Released

1.1

Important Data About this Machine

BNWCUD03.T01 0000189805 C.2 A.6 1/2/20 2:19 PM Released

Complete these two procedures before you use this machine:

1. Make sure that all laundry personnel are safe.

2. Change and make a check of the data contained in the memory of the machine (configuration,

formulas, and formula accumulator data).

1.1.1

Make Sure That All Laundry Personnel are Safe

BNWCUD03.C01 0000189804 C.2 A.6 1/2/20 2:19 PM Released

Personnel who will use or do maintenance on this machine must read the safety manual first.
Make all user manuals available to the correct personnel. Be sure that all personnel obey all pre-
cautions in the applicable manuals.

1.1.2

Change the Data

BNWCUD03.C02 0000189803 C.2 A.6 1/2/20 2:19 PM Released

1. Make sure that the controller configuration is correct for how you will use the machine.

2. Change the wash formulas if necessary for better results.

3. Make sure that you erased the formula count accumulator to make the formula count

accurate.

1.1.2.1

When to Change Data

BNWCUD03.C03 0000189802 C.2 A.6 1/2/20 2:19 PM Released

Make a check of the data:

•

when commissioning the machine

•

when required by error message

•

after replacing the microprocessor board

•

after upgrading the software

•

after adding or removing optional equipment

Make the necessary changes.

Pellerin Milnor Corporation

3

Summary of Contents for E-P Plus





























































































Reviews:

No comments