Milnor E-P Plus Reference Download Page 59 | Manualshive

Page: 59 / 92

Milnor E-P Plus Reference Download Page 59

Pellerin Milnor Corporation

53

or a Second Machine, page 50

for making a copy of good data

from the machine controller.
Confirms selection and advances to the

Data Transfer

menu.

DATA TRANSFER

0

SLAVE

The machine controller is set as the

Slave

device, making the stor-

age device the

Master

. The

Master

device always controls when

the data transfer starts and

sends

the data to the slave device. If

transferring data from one machine to another,

the slave machine

will receive the data sent from the master

.

Confirms the selection of the machine controller as the

Slave

device.

DATA TRANSFER **

PLEASE WAIT **

Appears for three seconds as the machine controller prepares ma-
chine memory to accept data from the storage device. When this
display appears, all memory in the machine controller is cleared.

PLEASE WAIT

0000

RECEIVING DATA

This display indicates that the machine controller is polling the
data storage device for incoming data. The four characters at the
right end of the top line show the memory location currently being
written. These characters remain at “0000” until the transfer
begins.

Press the

Transmit

button on the data storage device or confirm

the

Master

setting on the sending machine to begin the transfer.

As soon as the

Transmit

button on the data storage device is

pressed (or

on the master machine), the storage device begins

sending a continuous data stream to the slave machine controller.
The machine display shows the progress of this display in the four
characters on the top line. The transfer is complete when the dis-
play shows “FFFF.”

The

Transmit

light on the data storage device turns off when the

transfer completes.

E-PXPRESS/TxX
SYSTEMCORRECTIONAL
LAUNDRY

Appears for about one half second as the machine controller up-
dates all memory.

CONFIG CHKSUM

1234FORMULA CHKSUM
4321

Appears briefly (about one half second) as the machine controller
verifies that the checksums calculated for the downloaded data
match the checksums sent by the data storage device.

COMPLETED

0000

This display indicates that the data received by the machine con-
troller matches exactly the data sent by the storage device. The da-
ta transfer was successful.
Acknowledge that the data transfer is complete and returns to the

Program

menu.

PROGRAM

4

MENU

DATA TRANSFER

Data Transfer

menu display. Scroll to

Program

menu item

0

,

then turn the

Run/Program

keyswitch to the

Run

position.

Scroll the

Program

menu selections.

«
...
57
58
59
60
61
...
»

Summary of Contents for E-P Plus





























































































Reviews:

No comments