manualshive.com logo in svg

Milnor E-P Plus, Reference, Page: 78 / 92

Share
Download
Milnor E-P Plus Reference Download Page 78

72

Pellerin Milnor Corporation

displays the last 11 outputs (Page 1).

PAGE abcdefghijk

0

-+----+----

typical display of first page of outputs (Page 0) while the machine
is running. Refer to

Table 13: E-P Plus Outputs, page 65

to deter-

mine the component represented by each character on Page 0 and
Page 1.

4.1.8

Viewing Water Level and Temperature Data During

Operation

BNCJHT01.R07 0000191876 C.2 F.3 C.3 1/2/20 1:16 PM Released

Display or Action

Explanation

displays pressure transducer raw data and actual water level in
tenths

03:45 STEP #01 05:36
08240 081 080

LEV 2

From left to right, the bottom line displays the pressure transducer
raw data, the actual water level and the filtered water level in
tenths, and the desired level.
displays the calculated level, the desired level, and the
temperature

03:48 STEP #01 05:36
LC07/LD07/T103 LEV 2

From left to right, the bottom line displays the calculate water lev-
el, the desired water level, and the water temperature. The level
values on this display take into account any configured

offset

height

(see

2.3.4.2: The Configure Decisions, page 41

).

BNCJHT02 / 2018385

BNCJHT02

0000192158

B.3

1/2/20 1:16 PM

Released

4.2

Error Messages

BNCJHT02.C01 0000192157 C.2 B.3 A.8 1/2/20 1:16 PM Released

4.2.1

Error Messages at Power Up

BNCJHT02.T01 0000192156 C.2 B.3 A.8 1/2/20 1:16 PM Released

If an error message appears during power up, the error must be cleared before the machine can be
run or programmed.

Display or Action

Explanation

ACCUMULATOR ERROR

The microprocessor performs a memory check each time the ma-
chine is turned on. This error message appears if the microproces-
sor detects that the accumulator data is corrupt, in which case all
accumulators must be reset to zero.

TERMINATE TO CLEAR

Resets all accumulators and clears the error message. See

3.2:

How to Use and Erase the Formula Counter, page 60

for more

information.

CHECKSUM ERROR,TURN

Appears if there is illegal data in the configuration, formula, or in-
dustry memory areas. Use the following procedure to clear this
error.

KEY TO PROGRAM

Troubleshooting

Summary of Contents for E-P Plus





























































































Reviews:

No comments