Microsemi SmartTime User Manual Download Page 82

Page: 82 / 137

SmartTime Static Timing Analyzer User Guide

•

Speed

: STD

•

Die Voltage

: 1.2 V

•

Range

: COM

3. Click

Finish

to create the new project.

4. At the pop-up window, click

Use Enhanced Constraint Flow

in the New Project Information dialog

box.

Figure 60 · New Project Information Dialog Box

Import the false_path Verilog File and Add Constraints

You must import the false_path.v Verilog source file into your design for this tutorial. Cut-and-paste the
Verilog program from

false_path.v

to a file of the same name in a local directory.

Then run Libero SoC.

To import the Verilog Source File:

1. From the

File

menu, choose

Import > HDL Source Files

2. Browse to the location of the false_path.v you saved and select it. Click

Open

to import the file.

3. Verify that the file appears in your project, as shown in the figure below.

Summary of Contents for SmartTime










































































































































Search results

Summary of Contents for SmartTime

Reviews:

Related manuals for SmartTime

Brands by name

Popular brands

Microsemi SmartTime, User Manual

Search results

Summary of Contents for SmartTime

Reviews:

Related manuals for SmartTime

Brands by name

Popular brands