7 / 72
HBC-series V7 LV+MV
Accessories and options, available combination of HBC controllers
Controllers have in basic version only basic equipment. Features and options can significantly affect by the controller additional
equipment specifications.
Equipment of the controllers in the basic version:
- potentiometer input control (voltage control, 0 up to +3.3V)
- supply the control electronics from external source (battery) +14V up to +35V)
- ICS-2 connector for setting parameters, reading data from the controller, monitoring, update firmware, connection of external modules
- air cooler
- power cables soldered to the motherboard power, length 20 cm, cross section according to parameter table
- closed design
- screw-type connectors
Accessories and options:
For concrete hardware specification (or a custom firmware) and for order a specific configuration of the controllers, please
use the "HBC_ordering_form.xls". Not all combinations are available simultaneously. For questions or inquiries, please con-
tact directly the MGM compro.
Controller type you can specify in the order according to your specific requirements
Switch:
all controllers may be ordered with a switch (in a safe design - its damage or destroy does not affect the safety of flight
and the model / motor don´t stop working when switch component damaged
Heat sinks (coolers):
outer ribbed heat sinks (coolers) are delivered in standard basic version
Fans:
In case of insufficient cooling air flow can be ordered fans mounted to cooler - Active cooling (it is supplied as stand-
ard).
Fans can also be ordered separately as a complete kit with screws, which can add the controller addi-
tionally - use different types of fans and bolts is not allowed !!!
Water cooling:
version with water coolers is available for use in boats or in systems with higher demands for cooling intensity.
Capacitors axially:
controllers 18063, 25063, 100120, 140120 can be ordered with a capacitor mounted axially - It is especially important
for models without a fan or water-cooled types.
Hydro version
WP
:
water and humidity does not get on well with electronics. For significant increase of durability of the controller against
humidity and water, it is optionally possible to apply specialty protective cover (marked as
WP
). This however does
not mean that the controller with this protection is 100% durable during humidity and water and that it is not necessary
to protect it against these negative effects.
The protection does not apply to salt water at all !
Hydro version
WR
:
If you need high protection against water, moisture and dust, you can use controllers with
WR
modification. It is a
thick layer of special material on the PCB, more expensive solutions.
The protection does not apply to salt water at
all!
Sensor motors:
all types of controllers may be ordered suitable for sensor motors. These controllers may be connected to sensorless
motors as well as sensor motors. In this version is automatically available to the motor temperature measurement.
Battery temperature:
controllers have add measuring of battery temperature
Each cell monitoring:
all controllers have the option to measure each battery cell with an additional module BMM-16.
25063 controllers have the option of each battery cell to measure directly, without the module BMM-16.
Emergency disconnecting:
controllers 25063, 140120, can be ordered with a safety disconnection. Can be combined with the
Auto-connect circuits for traction.
Automatic traction connection:
controllers 25063, 140120, can be ordered with automatic traction connecting including antispark
access control circuit. This can be combined with a safety shutdown.
Control of braking resistors:
All types can be ordered with a connector and power management circuits for braking resistor switch
.
Communication:
All types can be ordered with a communication interface RS 232 TTL, RS 485 or CAN. Communication lines can be
galvanic isolated.
Telemetry:
All types can be ordered with options to connect Tx / Rx modules for telemetry (per channel RS-232 TTL)
.
Second ICS-2 connector:
controllers 25063, 140120, can be ordered with the second ICS-2 connector for easy connection of external modules.
Type of controls:
All types can be ordered with a control by voltage, PWM, potentiometer, data, logic and signal combinations. You can
also order two control channels (e.g. for a separate function brake / throttle)
.
Type of power connecting:
controllers 18063, 25063, 100120, 14012 can be ordered with either a power-soldered wires or soldered MPJET 5.0
connectors on the PCB or screw eyes for wire insertion. Wires can be soldered to the board either vertically or axially
(parallel to the plate). Next possibility is using ring terminals with corresponding cable.
Connectors types:
controllers 25063, 140120, can be ordered with different types of connectors on the control board.
The long data record:
if necessary, the record can be extended with external module LBB_RT with micro SD card on the length of the order
of months. The module is also available in a version with real time.
(§NA)
Cruise Control connection:
for all types is available external module CCM1, with which the cruise control function is provided.
Auxiliary DC/DC converter:
LV types (controllers up to 63V) can be ordered with an internal DC / DC converter supplying the auxiliary
+5 V or +12 V / 1 A
External display connecting:
for all types is available an external display module can be connected either via CAN (preferred) or via the Rx / Tx
port.
External modules connecting:
for all types of controllers can be connected external modules to an connector ICS-2
Customer changes:
if you need non-standard features or behavior of the controller, it is possible to agree on a customer change - please
contact the
MGM compro
.
