Luminaire settings
37
Clock
The Exterior 1200 Wash has a battery-operated 24-hour clock that is used to start and
stop stand-alone operation.
To set the clock:
1. Scroll through the MP-2 menus and select
A d j us t
→
R e a l t i m e c l o ck
.
2. Set the luminaire to the current time (expressed in the 24-hour clock in hours and
minutes) by scrolling through and entering values for
Ho u r
and
M in u t e
.
Luminaire settings
Luminaire settings are accessed under
P e rs o n a li t y
in the MP-2 menus.
D M X L a m p O f f a n d D M X R e s e t s e t t i n g s
If DMX will be used to control the luminaire, it is a good idea to set the DMX Lamp Off and
DMX Reset options via
P e r so n a l it y
→
D M X l a m p o f f
and
P er s o na l i t y
→
D MX
r e s et
. These settings are described in "
7.1: Preparing for DMX control"
The other default luminaire settings listed below are suitable for most applications, and it
may not be necessary to change them.
A u t o m a t i c l a m p o n
When
P e r so n a l it y
→
A u t o l a m p o n
is set to
O n
, the luminaire turns on the lamp
within 90 seconds of power on. When set to
O f f
(the default setting), a lamp-on
command from the DMX controller is required to turn on the lamp.
5 . 1 . 3 S e t t i n g u p a l u m i n a i r e w i t h t h e o n b o a r d
c o n t r o l p a n e l
DMX address
If you intend to use a DMX controller, you need to set the luminaire’s DMX address. If you
are not familiar with the principles of DMX addressing in an installation with multiple
fixtures, see "
To set the DMX address:
1. Press the
Menu
button to enter the main menu and use the
Up
and
Down
buttons if
necessary to select
F ix t u r e a d d re s s
.
2. Press
Enter
.
3. Use
Up
and
Down
to enter a value between 1 and 505 (512 DMX channels are
available in one DMX universe, and the Exterior 1200 Wash uses 8 channels).
Pressing
Up
and
Down
simultaneously sets the DMX address to 1.
4. Press
Enter
to confirm your choice and return to main menu. If you press
Menu
, you
will return to the main menu without saving the address you entered.
Clock
The Exterior 1200 Wash has a battery-operated 24-hour clock that is used to start and
stop stand-alone operation.
To set the clock:
1. If the display is showing
F i x tu r e s t at u s
and
L a mp st a t u s
, press
Menu
to enter
the main menu. Scroll down to
P e rs o n a li t y
. and press
Enter
.
Summary of Contents for Exterior 1200 Wash
