background image

Luminaire settings

35

Luminaire settings

To access the luminaire settings using MUM, click on the 

Fixture settings

 button.

D M X   a d d r e s s ,   D M X   L a m p  O f f   a n d   D M X   R e s e t   s e t t i n g s

If you intend to operate the Exterior 1200 Wash with a DMX controller, the DMX address 
must be set on all luminaires for which individual control is required. If you are not familiar 
with the principles of DMX addressing in an installation with multiple fixtures, see "

7.1.1: 

Setting DMX addresses"

 on page 50.

It is also a good idea to set the 

DMX Lamp Off

 and 

DMX Reset

 options. These settings 

are described in "

7.1: Preparing for DMX control"

 on page 50.

The other default luminaire settings listed below are suitable for most applications, and it 
may not be necessary to change them.

A u t o m a t i c   l a m p   o n

When the 

Automatic Lamp On

 personality is 

On

, the luminaire turns on the lamp within 

90 seconds of power on. When set to 

Off

 (the default setting), a lamp-on command is 

required to turn on the lamp. 

Summary of Contents for Exterior 1200 Wash





















































































Reviews: