IMPULSE•VG+ Series 3 Instruction Manual – 07/25/05
5-58
Parameter
Code
Display
Function
Range
Initial
Value
Access
Level
F1-08
PG Overspd Level
Motor overspeed detection level.
0–120%
105
Adv
F1-09
PG Overspd Time
Motor overspeed detection time.
0–2.0 sec
0.0
Adv
F1-10
PG Deviate Level
Excessive speed deviation level.
0–50%
10
Adv
F1-11
PG Deviate Time
Excessive speed deviation time.
0–10.0 sec
0.3
Adv
F1-12
PG# Gear Teeth 1
PG Reduction Ratio
0-1000
0
Adv
F1-13
PG# Gear Teeth 2
PG Reducion Ratio
Ratio = 60 x F1-13
F1-12
Note: A Gear ratio of 1 will be
used if either perameter = 0
0-1000
0
Adv
F1-15
PGO Detect Time
Open encoder circuit
0.00-10.00
0.50
Adv
F1-16
PG Ch 2 PPR
Indicates how many pulses the
drive can expect per revolution of
the motor.
1-60000 PPR
1024
Adv
F1-17
PG Ch 2 Rotation
O-FWD = CCW
1 - FWD = CW
0-1
0
Adv
F1-18
PGO-2-S Det Time
Channel 2 open encoder circuit
0-10.0 Sec
0.5 Sec
Adv
F1-19
PG-Z2 Output Set
PG-Z2 Output
0-3
2
Adv
0
Select by MFI=41
1
Channel 1
2
Channel 2
3
Select by MFI=64
F1-20
PGO-1-H 0/1
CH1 Hardware PGO
enable/disable
0-1
1
Adv
0
Disabled
1
Enabled
F1-21
PGO-2-H 0/1
CH2 Hardware PGO
enable/disable
0-1
0
Adv
0
Disabled
1
Enabled
F1-22
PG-Z2 Input Sel
Option Card PG-Z2 channel
select
0-1
0
Adv
0
Ch1 = motor 1, Ch 2 = motor 2
1
Ch 2 = motor 2, Ch 2 = motor 1
* Factory setting changes based on Control Method (A1-02)
Summary of Contents for IMPULSE VG+ Series 3
