![background image](http://html1.mh-extra.com/html/mack/e7/e7_service-manual_3065456174.webp)
Page 6-16
200 ENGINE ASSEMBLY
Refer to Figure 6-17.
1. Using piston cooling nozzle spray position
set J 37721-A (pre-1991) or J 39045 (1991
and later), check the direction of the spray
from the nozzles.
2. Position rod (6) in end of spray nozzle (7).
3. Place the applicable plastic target (1) on the
cylinder block (2) over the cylinder to be
tested.
4. Install a cylinder head bolt through the target
alignment hole (3) and into the cylinder block
capscrew hole (4) to align the target.
5. The rod (6) should now be aligned in the
target area (5). If rod is at edge of target
area, two methods may be tried to center the
rod into the target area.
a.
Preferred — Loosen nozzle set screw.
A slight adjustment can then be made
to center the rod within the target area.
Following adjustment, retorque set
screw to 15 lb-ft (20 N
폷
m).
b.
Alternate (pre-1991 only) — It is
permissible to bend the hooked end of
the nozzle tube
only slightly
to bring
the rod fully within 1/8 inch of the target
area. If more than 1/8 inch out of target
area, replace nozzle.
Figure 6-17 — Spray Nozzle Targeting
1. Plastic target
2. Cylinder block
3. Alignment hole
4. Cylinder block hole
5. Target area
6. Rod
7. Spray nozzle
200281a
1
2
3
4
5
6
7
5-101.bk Page 16 Friday, March 17, 2006 11:05 AM
Summary of Contents for E7
