Life technologies invitrogen Neon User Manual Download Page 29

Page: 29 / 52

Using the Neon

™

Transfection System,

Continued

Electroporation
Protocol,

Continued

17.

Repeat Steps 7–16 for the remaining samples.

Be sure to change the Neon

™

Tips after using it twice and Neon

™

Tubes

after 10 usages. Use a new Neon

™

Tip and Neon

™

Tube for each new

plasmid DNA sample.

18.

Gently rock the plate to assure even distribution of the cells. Incubate the
plate at 37°C in a humidified CO

incubator.

19.

If you are not using the Neon

™

device, turn the power switch on the rear

OFF

20.

Assay samples to determine the transfection efficiency (e.g., fluorescence
microscopy or functional assay) or gene knockdown (for siRNA).

Optimization

Based on your initial results, you may need to optimize the electroporation
parameters for your cell type. See page 22 for using the 18-well or
preprogrammed 24-well optimization protocol on the Neon

™

device.

Cleaning and
Maintenance

Clean the surface of the Neon

™

device and Neon

™

Pipette Station with a damp

cloth.

Do not

use harsh detergents or organic solvents to clean the unit. The

Neon

™

Pipette is permanently calibrated at the manufacturer and does not

require any further calibration.

Important!

Avoid spilling any liquid inside of the Neon

™

Pipette Station to

prevent any build up of rust on the ball plunger in the pipette station.

In case you accidentally spill any liquid (e.g., buffer, water, coffee) inside the
Neon

™

Pipette Station, disconnect the station from the main device and wipe

the station using dry laboratory paper. Invert and allow the station to
completely dry for 24 hours at room temperature.

Do not use the oven to dry

the Neon

™

Pipette Station.

If the station does not work after drying, contact

Technical Support (page 39).

For any other repairs and service, contact Technical Support (page 39).

Do not

perform any repairs or service on the

Neon

™

device yourself as it is a high

voltage hazard and to avoid any damage to the unit or voiding your warranty.

Summary of Contents for invitrogen Neon





















































Search results

Summary of Contents for invitrogen Neon

Reviews:

Related manuals for invitrogen Neon

Brands by name

Popular brands

Life technologies invitrogen Neon, User Manual

Search results

Summary of Contents for invitrogen Neon

Reviews:

Related manuals for invitrogen Neon

Brands by name

Popular brands