LG 42LY770M Page 79 Commercial Mode Setup Manual Download

Page: 79 / 104

206-4271

Reference:

-LAN Setup & Overview

-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system

to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded

-LAN module to receive communication from the head end device. At this point, if it is desired for the

-LAN

module to always be powered, including while the TV is turned OFF, set Installer Menu item 118 POWER

SAVINGS to 1.
Also, if MPI communication is required for external MPI control, set Installer Menu item 118 POWER SAVINGS

to 1 so that the GAME CONTROL/MPI port circuitry is always powered.

Caution: POWER SAVINGS should NEVER be set to 7. This setting is intended for factory use

only.

The

-LAN module is internal to the TV. It allows hospital/institution head end equipment with

-LAN technology

to communicate, via the institution’s RF distribution system, with the TV for configuration and control.
Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded

-LAN module

and the GAME CONTROL/MPI port. The default value is 3—the

-LAN module is only powered when the TV

is turned ON. See chart below.

POWER

SAVINGS

3 (default)

Off

TV ON

TV OFF

-LAN &

GAME

CONTROL/MPI Port

Power

-LAN

GAME

CONTROL/MPI Port

Power

Summary of Contents for 42LY770M









































































































Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands

LG 42LY770M, Commercial Mode Setup Manual

Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands