LG 42LY770M Page 44 Commercial Mode Setup Manual Download

Page: 44 / 104

206-4271

Value

Status

Speaker Output

Fixed 0.01 Watts

Fixed 0.03 Watts

Fixed 0.05 Watts

Fixed 0.10 Watts

Fixed 0.20 Watts

Fixed 0.50 Watts

Fixed 1.00 Watt (default)

Control with volume

Line Output

Fixed line level (typically 400 mVrms ±

100 mVrms @10KΩ)

output

098 - PRO:CENTRIC

Selects the Pro:Centric Application Mode. Set to 0 (default) to

disable the Pro:Centric application. Set to 1 for Flash Mode. Set

to 2 for GEM (Java Application) Mode. Set to 3 for HTML Mode.
The TV must be turned OFF for a few seconds to initiate the

Pro:Centric application download. When the TV is turned back ON,

it may take several minutes to load the Pro:Centric application after

the initial download.

Note:

This item is not available in the Installer Menu when item

119 DATA CHANNEL is set to 0.

099 - BACK LIGHTING

Sets the TV screen brightness at power up. Default setting is 255.

•

1 (dimmest picture) – 100 (brightest picture) Static Back Lighting

•

101

(dimmest picture) –

200 (brightest picture) Dynamic Back

Lighting: The TV automatically controls back lighting depending

upon the picture level of the current program.

•

201 Automatic Static Back Lighting: The TV automatically

controls back lighting by using Intelligent Sensor to detect the

level of ambient lighting.

•

202 Automatic Dynamic Back Lighting: The TV automatically

controls back lighting by using Intelligent Sensor to detect the

level of ambient lighting and depending upon the picture level

of the current program.

If set to 201 or 202, back lighting can be controlled via the Picture

settings in the TV setup menus. However, each time the TV is

turned ON, Picture Mode (set in Picture Menu) is defaulted to

Intelligent Sensor. If Picture Mode is manually set to a static option

(Vivid, Standard, etc.) during a viewing session, Intelligent Sensor

is temporarily disabled.
If set to 255, back lighting is controlled via the Picture settings in

the TV’s setup menus.

101 - IR FEEDBACK

If set to 0 (default), the TV’s MMR (Magic Motion Remote) feature

is enabled, and a compatible LG MMR (not supplied) may be used

with the TV. If set to 2, the MMR feature is disabled.

102 - ATSC BAND

Sets up TV to receive different types of incoming signals:
0 = Broadcast

1 = CATV

2 = HRC

3 = IRC

4 = Same as NTSC

103 - ATSC TUNE MODE

Sets ATSC tuning mode. Default set to 1 for Physical Channel

scan. Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL

Sets Minor Start Channel number at power up. 0 = NTSC. If not

0, number selected is the digital channel’s Minor Start Channel

number.

Note:

This item is not available in the Installer Menu when item

004 STRT CHANNEL is set to 0 or 255.

106 - ASP RATIO LOCK (Aspect Ratio Lock)

Set to 1 to retain previous aspect ratio with power off. Set to 0 to

retain default aspect ratio with power off. See item 096 DEF. ASP.

RATIO above.

116 - VIDEO MUTE EN (Video Mute Enable)

Applicable for analog channels only. If set to 1, video mutes

(blank screen) when no signal is present.

117 - FACT DEFAULT (Factory Default)

Set to 1 and press OK to restore the factory default settings of all

Installer Menu items. Once complete, the value returns to 0.

Caution:

If set to 1, this clears all Installer Menu custom

settings and restores the factory default settings. It also

clears the channel lineup, including any assigned

channel icons and custom text labels.

Note:

See also Reference section, “Restoring Factory Defaults on

the TV(s),” for further information.

118 - POWER SAVINGS

Default set to 3—the power circuitry for both the embedded

-LAN

module and the GAME CONTROL/MPI port is only powered when

the TV is turned ON. When the TV is turned OFF, the embedded

-LAN and the GAME CONTROL/MPI port are not powered.

Note that the TV must be turned ON in order to communicate with

the embedded

-LAN module for configuration and control when

POWER SAVINGS is set to 3. If POWER SAVINGS is set to 1,

the

-LAN module is always powered.

Similarly, if MPI communication is required for external MPI

control, POWER SAVINGS should be set to 1 so that the GAME

CONTROL/MPI port circuitry is always powered.

Note:

See Reference section, “

-LAN Setup & Overview,” for

further information.

Caution: POWER SAVINGS should NEVER be set to 7.

This setting is intended for factory use only.

Installer Menu (Cont.)

Summary of Contents for 42LY770M









































































































Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands

LG 42LY770M, Commercial Mode Setup Manual

Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands