LG 42LY770M Page 36 Commercial Mode Setup Manual Download

Page: 36 / 104

206-4271

As part of the Installer Menu header (in all modes), two 3-character acronyms are displayed to indicate

the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV

models.

Acronym

Description

CPU-CTV

Pass-through Mode with Channel Lineup in CPU

CPU-FTG

FTG Mode via CPU

CPU-P:C

Application Tuning Mode via CPU

EBL-FTG

FTG Mode via EBL

EBL-LNT

SONIFI PPV Mode

MPI-EXT

External MPI Control

PTC-CTV

Pass-through Mode with Channel Map in PTC

Using the Installer Menu

Refer to the table starting on the next page for an overview of the available Installer Menu items,

including their item numbers, functions, value ranges, and default values.
Installer Menu items not relevant to these TV models are not present in the Installer Menu; therefore,

some numbers are missing. For example, item 006 will not appear. In addition, items that are

dependent on other Installer Menu item settings will not be initially accessible. For example, item 046

STRT AUX SRCE will not display in the Installer Menu unless item 004 STRT CHANNEL is set to 0.

See Installer Menu detailed descriptions for further information.

Navigation within the Installer Menu

Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu items,

or access an item directly by keying in the item number and then pressing

MENU

. For example, to

access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU.

Changing Installer Menu Settings

To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or

enter a valid value directly. To save the new setting, press

, or use the Up/Down arrow keys to

navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will

not be saved.

Exiting the Installer Menu and Activating Settings

After you have adjusted all required Installer Menu item settings, press

once on the Installer

Remote to save your changes; then, press

again to exit the Installer Menu. Any changes you

make will be stored in non-volatile memory.

Note:

Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control)

settings in the TV are reset to their default values; that is, the Lock System, if previously enabled from

the Safety Menu, will now be disabled, and the individual Parental Control settings will be restored

to default values.

Installer Menu (Cont.)

Caution: Installer Menu settings may affect options available

from the TV setup menus or the Function Menu.

Summary of Contents for 42LY770M









































































































Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands

LG 42LY770M, Commercial Mode Setup Manual

Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands