LG 42LY770M Page 42 Commercial Mode Setup Manual Download

Page: 42 / 104

206-4271

032 - TIMING PULSE

MPI Communication Parameter. Sets baud rate for MPI. Step size

of 4.3 uS. Changing from default may affect communication via

MPI.

035 - HDMI1 ENABLE

Set to 1 to enable HDMI 1 input in DTV Mode. Set to 2 to enable

HDMI 1 input in PC Mode. Set to 0 to disable display panel HDMI

1 input.

039 - REAR AUX EN. (Rear Aux Enable)

Set to 1 to enable display panel rear Aux (AV) input. Set to 0 to

disable display panel rear Aux (AV) input.

041 - SIMPLINK EN

Set to 0 to disable the SIMPLINK feature. Set to 1 to enable

SIMPLINK functionality (does not enable remote control access to

the SIMPLINK Menu).

Note:

When both this item

and

item 042 AUTO INPUTS are

enabled in the Installer Menu, HDMI inputs will be detected by

SIMPLINK, but the Auto Input(s) Sensing Feature will not function.

042 - AUTO INPUTS

Determines the Aux inputs for which auto-sensing is enabled. Set

to 0 to disable auto-sensing for all available inputs. Set to 255 to

enable auto-sensing for all available inputs. For information on

options for individual input settings, see Reference section, “Auto

Input(s) Sensing Feature.”

Note:

In order for auto-sensing to be enabled for an input, that

input must also be enabled in the Installer Menu. For example, to

enable auto-sensing for HDMI 1, item 035 HDMI1 ENABLE must

also be set to 1 or 2. Also, see note above regarding TV operation

when both this item and item 041 SIMPLINK EN are enabled.

046 - STRT AUX SRCE (Start Aux Source)

Sets the starting Aux source. When turned ON, the TV will tune to

starting Aux source if item 004 STRT CHANNEL is set to 0.
1 = AV

5 = HDMI 2

3 = HDMI 1

255 = Last Aux

Note:

Above is applicable only if all Aux sources are enabled.

Note:

This item is not available in the Installer Menu unless item

004 STRT CHANNEL is set to 0.

047 - AUX STATUS

Set to 1 for MPI Aux source to be reported as a channel number

instead of channel 0. Set to 0 to disable Aux identification change.

Controls MPI status channel response for Aux inputs.

049 - DIS. AUDIO M. (Disable Audio Menu)

Determines the availability of the Sound Out (Audio) Menu in the

TV menus. Also determines the default Audio Mode when TV is

turned ON. See the table below and set as required.

Value

Sound Out (Audio)

Menu Status

Default Audio Mode at TV

Turn ON

0 (default)

Enabled

Internal TV Speaker

Disabled

Internal TV Speaker

Enabled

External Speaker (optical or HDMI)

Disabled

External Speaker (optical or HDMI)

Enabled

LG Sound Sync (optical)

Disabled

LG Sound Sync (optical)

Enabled

LG Sound Sync (BT wireless)

Disabled

LG Sound Sync (BT wireless)

Note:

If a SIMPLINK-enabled device is connected to the TV

and item 041 SIMPLINK EN is set to 1 (enabled), the SIMPLINK

device Audio Mode will have priority over the setting of this item

when the TV is turned ON.

Note:

Items 020 FEATURE LEVEL and 027 HOSPITAL MODE

have priority over the setting of this item. Thus, if either item 020 or

027 is set to a Pillow Only value and this item is set to an internal

TV speaker value, the pillow speaker setting will have priority, and

you will not be able to hear sound from the TV speaker. You may

however, set an external speaker configuration in conjunction with

the pillow speaker.

Note:

When this item is set to 6 or 7, the Bluetooth Sound Sync

Media Share feature is not available. If Bluetooth Sound Sync is

currently enabled in the IP Environment / Media Share Menu, it

will be disabled.

053 - DIS. CH-TIME (Disable Channel-Time)

Set to 1 to disable the Channel-Time display; Channel-Time display

will not appear. Set to 0 to enable the Channel-Time display.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)

Set to 1 to enable custom color for the Channel-Time display. Set

to 0 to disable custom color for the Channel-Time display.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)

Set according to Color Chart:
0 = Black

3 = Cyan

6 = Yellow

1 = Blue

4 = Red

7 = White

2 = Green

5 = Violet

Note:

If foreground color and background color are the same, the

menu background will be transparent.

Note:

Applies only to “Channel Not Available” message if item

073 CH NOT AVBLE is set to 1 (enabled). Also, items 070 FOR.

CH-TIME and 071 BCK. CH-TIME are not available in the Installer

Menu when item 069 EN. CH-T COL. is set to 0.

071 - BCK. CH-TIME (Channel-Time Display Background Color)

See description for item 070 FOR. CH-TIME above. The color

chart is the same for both items.

Installer Menu (Cont.)

Summary of Contents for 42LY770M









































































































Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands

LG 42LY770M, Commercial Mode Setup Manual

Search results

Summary of Contents for 42LY770M

Reviews:

Related manuals for 42LY770M

Brands by name

Popular brands