LevelOne IES-0883 User Manual Download

Page: 114 / 152

IES-0883 User Manual

Page 113

The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use this command to set the switching characteristics of the Layer-2 interface to trunk.

The all parameter indicates that any VLAN ID is part of its port’s member set. The none

parameter indicates that no VLAN ID is configured on this port. The add and remove
parameters will add and remove VLAN IDs to/from the port’s member set.

Use the no parameter to remove all VLAN IDs configured on this port.

Command Syntax:

switchport trunk allowed vlan all
switchport trunk allowed vlan none

switchport trunk allowed vlan add VLANID

switchport trunk allowed vlan remove VLANID

switchport trunk allowed vlan except VLANID

no switchport trunk vlan

all Allow all VLANs to transmit and receive through the Layer-2 interface.

none Allow no VLANs to transmit and receive through the Layer-2 interface.

add Add a VLAN to transmit and receive through the Layer-2 interface.

remove Remove a VLAN from transmit and receive through the Layer-2 interface.

except All VLANs, except the VLAN for which the ID is specified, are part of its ports
member set.

VLANID <2-4094> The ID of the VLAN or VLANs that will be added to, or removed from,

the Layer-2 interface. A single VLAN, VLAN range, or VLAN list can be set.

For a VLAN range, specify two VLAN numbers: lowest, then highest number in the range,

separated by a hyphen.
For a VLAN list, specify the VLAN numbers separated by commas.

Example:

The following example specifies to

add

the interface fe1 (port 1) to VLANID (

switch_a(config)#interface fe1
switch_a(config-if)#switchport trunk allowed vlan add 2

switch_a(config-if)#

Port Based VLAN

Switchport portbase add/remove vlan:

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).
Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands