LevelOne IES-0883 User Manual Download

Page: 117 / 152

IES-0883 User Manual

Page 116

Strict Priority:
1.

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

priority-queue out

command to enable the egress expedite queue.

Use the

no priority-queue out

command to disable the egress expedite queue.

Command Syntax:

(no) priority-queue out

Example:

The following example enables the egress expedite queue on the switch:

switch_a(config)#priority-queue out

switch_a(config)#

Weighted Round Robin:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

wrr-queue bandwidth

command to specify the bandwidth ratios of the transmit

queues.

Command Syntax:

wrr-queue bandwidth WRR_WTS

WRR_WTS Weighted Round Robin (WRR) weights for the 4 queues (4 values separated by
spaces). Range is 1-55.

Example:

The following example specifies the bandwidth ratios of the transmit queues on the

switch:

switch_a(config)#wrr-queue bandwidth 1 2 4 8

switch_a(config)#

802.1p Priority

Command Mode: Configure mode

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands