LevelOne IES-0883 User Manual Download Page 20

Page: 20 / 152

IES-0883 User Manual

Page 19

Alarms for Power Failure

Step 1: There are two pins on the terminal block used for power failure detection. It

provides the normally closed output when the power source is active. Use this as a

dry contact application to send a signal for power failure detection.

rmin

PW1

12 – 32VDC

–

Power Ground

PW2

12 – 32VDC

–

Power Ground

Earth Ground

Relay Output

1A @ 24VDC

Relay Alarm warning signal disable for following:
5.

The relay contact closes if Power1 and Power2 are both failed but Power3 on

The relay contact closes if Power3 is failed but Power1 and Power2 are both on

Special note:
The relay output is normal open position when there is no power to the switch.
Please do not connect any power source to this terminal to prevent shorting your
power supply.

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands