LevelOne IES-0883 User Manual Download Page 96

Page: 96 / 152

IES-0883 User Manual

Page 95

Trunking

Port Trunking

Port Trunking

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

fe1 means port 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface fe1

switch_a(config-if)#

Usage:

Use

static-channel-group

command to create a static aggregator, or add a member port

to an already-existing static aggregator.
Use the

no static-channel-group

command to detach the port from the static

aggregator.

Command Syntax:

static-channel-group <1-3>
no static-channel-group

<1-3> Channel group number.

Maximum 4 ports in static-channel-group 1 and static-channel-group 2.

Maximum 2 ports in static-channel-group 3

Example:

The following example adding the interface fe1 (port 1) to

static-channel-group 1

switch_a(config)#interface fe1

switch_a(config-if)#static-channel-group 1

switch_a(config-if)#

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands