LevelOne IES-0883 User Manual Download Page 35

Page: 35 / 152

IES-0883 User Manual

Page 34

Firmware Upgrade

Filename: Click in “Filename” text box and type the name of the file that you intend to

upgrade it to the switch.

TFTP server IP: Click in “TFTP server IP” text box and type the TFTP server IP address

from where the file will be obtained.

Upgrade: Click “upgrade” button to upgrade firmware to the switch. Please follow the

message on the screen during the firmware upgrade process. Do not turn off the

power or perform other functions during this period of time. Reboot the switch after
completing the upgrade process.

Please follow the message on the screen during the firmware upgrade process. Do not

turn off the power or perform other functions during this period of time.

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands