LevelOne IES-0883 User Manual Download

Page: 116 / 152

IES-0883 User Manual

Page 115

QoS

Global Configuration, 802.1p Priority, DSCP

Global Configuration

QoS:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

mls qos enable

command to globally enable QoS.

Use the

no mls qos

command to globally disable QoS.

Command Syntax:

mls qos enable
(no) mls qos

Example:

The following example globally enables QoS on the switch:

switch_a(config)#mls qos enable

switch_a(config)#

Trust:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

mls qos trust

command to turn on QoS trust CoS or DSCP.

Use the

no mls qos trust

command to turn off QoS trust CoS or DSCP.

Command Syntax:

(no) mls qos trust cos/dscp
cos Class of Service.

dscp Differentiated Service Code Point.

Example:

The following example turns on QoS trust CoS on the switch:

switch_a(config)#mls qos trust cos

switch_a(config)#

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands