LevelOne IES-0883 User Manual Download Page 11

Page: 11 / 152

IES-0883 User Manual

Page 10

Product Highlights

Basic Features

•

Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial
environment.

•

Manageable via SNMP, Web-based, Telnet, and RS-232 console port.

•

Supports Command Line Interface in RS-232 console.

•

Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation:
10/100/1000Mbps, full/half-duplex. Auto MDI/MDIX.

•

1000Base-SX/LX: Multi mode or Single mode SC type, 1000Base-BX: WDM Single mode
SC type.

•

Supports 4096 MAC addresses. Provides 1M bits memory buffer.

•

Store-and-forward mechanism.

•

Full wire-speed forwarding rate.

•

Alarms for power failure by relay output.

•

Operating voltage and Max. current consumption: 1.7A @ 12VDC, 0.85A @ 24VDC.

Power consumption: 20.4W Max.

•

Power supply: Redundant DC Terminal Block power inputs and 12VDC DC JACK with
100-240VAC external power supply.

•

Field Wiring Terminal Markings: Use Copper Conductors Only, 60/75

℃

, wire range

12-24 AWG, torque value 7 lb-in.

•

-20

℃

to 60

℃

(-4

℉

to 140

℉

) operating temperature range. UL508 Industrial Control

Equipment certified Maximum Surrounding Air Temperature @ 60

℃

(140

℉

•

For use in Pollution Degree 2 Environment.

•

Supports DIN-Rail and Panel Mounting installation.

Management Support

VLAN

Port-based VLAN

IEEE802.1Q tagged VLAN

TRUNKING

MAC-based Trunking with automatic link fail-over

PORT-SECURITY

Per-port programmable MAC address locking

Up to 24 Static Secure MAC addresses per port

IEEE802.1x Port-based Network Access Control

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands