LevelOne IES-0883 User Manual Download

Page: 133 / 152

IES-0883 User Manual

Page 132

Other Protocols

GVRP, IGMP Snooping, NTP

GVRP

GVRP:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

set gvrp enable bridge

command to enable (set) and

set gvrp disable bridge

command to disable (reset) GVRP globally for the bridge instance. This command does not
enable/disable GVRP in all ports of the bridge. After enabling GVRP globally, use the

set

port gvrp enable

command to enable GVRP on individual ports of the bridge.

Command Syntax:

set gvrp enable bridge GROUP

set gvrp disable bridge GROUP

GROUP Bridge-group ID used for bridging.

Example:

The following example globally enables GVRP to bridge GROUP (

switch_a(config)#set gvrp enable bridge 1

switch_a(config)#

Dynamic VLAN creation:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

set gvrp dynamic-vlan-creation enable bridge

command to enable and

set gvrp

dynamic-vlan-creation disable bridge

command to disable dynamic VLAN creation for a

specific bridge instance.

Command Syntax:

set gvrp dynamic-vlan-creation enable bridge GROUP

set gvrp dynamic-vlan-creation disable bridge GROUP

GROUP Bridge-group ID used for bridging.

Example:

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands