LevelOne IES-0883 User Manual Download

Page: 80 / 152

IES-0883 User Manual

Page 79

IP Address

IP Address/IP Subnet Mask:
1.

Command Mode: Interface mode

Logon to Configure Mode (Configure Terminal Mode).

Then logon to Interface mode.

vlan1.1 means vlan 1.
The

switch_a(config-if)#

prompt will show on the screen.

switch_a(config)#interface vlan1.1
switch_a(config-if)#

Usage:

Use

ip address

command to set the IP address of an interface.

Use the

no ip address

command to remove the IP address from an interface.

Command Syntax:

ip address IP-ADDRESS

no ip address IP-ADDRESS

no ip address

IP-ADDRESS A.B.C.D/M specifies the IP address and prefix length of an interface.

M specifies IP subnet mask, 8: 255.0.0.0, 16:255.255.0.0, 24: 255.255.255.0.

Example:

The following example sets the new IP address

192.168.1.10

and new IP subnet mask

255.255.255.0

to switch:

switch_a(config)#interface vlan1.1

switch_a(config-if)#ip address 192.168.1.10/24

switch_a(config-if)#

Default Gateway:

Command Mode: Configure mode

Logon to Configure Mode (Configure Terminal Mode).
The

switch_a(config)#

prompt will show on the screen.

switch_a(config)#

Usage:

Use

ip default-gateway

command to set the IP address of the default gateway.

Use the

no ip default-gateway

command to remove the IP address of the default

gateway.

Command Syntax:

ip default-gateway IP-ADDRESS

no ip default-gateway

IP-ADDRESS A.B.C.D specifies the IP address of the default gateway.

Example:

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands