LevelOne IES-0883 User Manual Download

Page: 7 / 152

IES-0883 User Manual

Page 6

Functional Description

•

Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial
environment.

•

Manageable via SNMP, Web-based, Telnet, and RS-232 console port.

•

Supports Command Line Interface in RS-232 console.

•

Supports IEEE802.3/802.3u/802.3ab/802.3z/802.3x. Auto-negotiation:

10/100/1000Mbps, full/half-duplex. Auto MDI/MDIX.

•

1000Base-SX/LX: Multi mode or Single mode SC type, 1000Base-BX: WDM Single mode

SC type.

•

Supports 4096 MAC addresses. Provides 1M bits memory buffer.

•

Store-and-forward mechanism.

•

Full wire-speed forwarding rate.

•

Alarms for power failure by relay output.

•

Operating voltage and Max. current consumption: 1.7A @ 12VDC, 0.85A @ 24VDC.
Power consumption: 20.4W Max.

•

Power supply: Redundant DC Terminal Block power inputs and 12VDC DC JACK with

100-240VAC external power supply.

•

Field Wiring Terminal Markings: Use Copper Conductors Only, 60/75

℃

, wire range

12-24 AWG, torque value 7 lb-in.

•

-20

℃

to 60

℃

(-4

℉

to 140

℉

) operating temperature range. UL508 Industrial Control

Equipment certified Maximum Surrounding Air Temperature @ 60

℃

(140

℉

•

For use in Pollution Degree 2 Environment.

•

Supports DIN-Rail and Panel Mounting installation.

Console Configuration

Connect to the switch console:

Connect the DB9 straight cable to the RS-232 serial port of the device and the RS-232

serial port of the terminal or computer running the terminal emulation application.

Direct access to the administration console is achieved by directly connecting a

terminal or a PC equipped with a terminal-emulation program (such as HyperTerminal)

to the switch console port.

Configuration settings of the terminal-emulation program:

Baud rate: 115,200bps

Data bits: 8

Parity: none

Stop bit: 1

Flow control: none

Press the “Enter” key. The Command Line Interface (CLI) screen should appear as below:

Logon to Exec Mode (View Mode):

At the “switch_a login:

”

prompt just type in “root” and press <Enter> to logon to Exec

Mode (or View Mode). And the “switch_a>” prompt will show on the screen.

Summary of Contents for IES-0883

























































































































































Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands

LevelOne IES-0883, User Manual

Search results

Summary of Contents for IES-0883

Reviews:

Related manuals for IES-0883

Brands by name

Popular brands