manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 86 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 86

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

86

12

Error messages

12.2

Possible causes and remedies

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

EtherNet/IP: Class 3 Connection Closed [0x00c88143]

EtherNet/IP: Duplicate IP address [0x00c88273]

Response 

(Lenze setting printed in bold)

Setting:

 not possible

None

System fault

Fault

Trouble

Quick stop by trouble

Warning locked

Warning

Information

Cause

Remedy

Scanner has closed a "Class 3" connection.

Check scanner functionality.

Response 

(Lenze setting printed in bold)

Setting:

 not possible

None

System fault

Fault

Trouble

Quick stop by trouble

Warning locked

Warning

Information

Cause

Remedy

An IP address has been allocated twice within the 

network. The addresses of the network nodes must differ 

from each other.

Correct IP address (

C13000

/ 

C14000

).

Setting the IP configuration of the Servo Drive 9400 

(

37)

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments