manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 61 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 61

8

I/O data transfer (implicit messages)

8.3

I/O configuration with »RSLogix 5000« version 19 or lower

61

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

7. Under 

I/O Configuration

 in the configuration tree, right click "1769-L32E Ethernet Port 

LocalENB" and select "Properties".

8. Go to the 

Connection

 tab and set further properties.

Required settings

Optional settings

Setting

Description

Requested Packet 

Interval (RPI)

Set 

RPI 

2.0 ms

. (Standard setting: 10 ms)

The RPI [ms] specifies the intervals for the I/O data exchange between the drive 

(adapter) and the controller (scanner).

Use Unicast Connection 

over EtherNet/IP

Option deactivated (standard setting):

• The input data is sent from the adapter to the scanner by means of 

multicast 

telegrams

.

• Other scanners can access this data in addition to the currently configured 

scanner ("Listen only" or "Input only" connections).

Option activated:

The input data is sent from the adapter to the scanner by means of 

unicast 

telegrams

.

Settings

Description

Inhibit module

This option serves to interrupt or inhibit the communication to the adapter.

Major Fault On 

Controller If Connection 

Fails While In Run Mode

This option serves to put the scanner into the error status if the EtherNet/IP 

connection to the drive (adapter) fails while the scanner is in operation.

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments