manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 95 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 95

13

Parameter reference

13.2

Parameters of the communication module for slot MXI1

95

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

C13022

C13840

C13841

Parameter | Name:

C13022 | Quality of Service (DSCP)

Data type: UNSIGNED_8

Index: 11553 = 0x2D21

Setting for the prioritisation of the data packets to be transferred using Differentiated Services Codepoints (DSCP)

Setting range 

(min. value | unit | max. value)

0

63

Subcodes

Lenze setting

Info

C13022/1

59

Reserved

C13022/2

47

Reserved

C13022/3

55

Reserved

C13022/4

47

QoS DSCP Scheduled

(Instance attribute 5 (DSCP Scheduled) in the 

Quality of 

Service (QoS) Object (72 / 0x48) (

130)

)

C13022/5

43

QoS DSCP High Prio

(Instance attribute 6 (DSCP High Prio) in the 

Quality of 

Service (QoS) Object (72 / 0x48) (

130)

)

C13022/6

31

Reserved

C13022/7

27

QoS DSCP Explicit Msg

(Instance attribute 8 (DSCP Explicit Msg.) in the

Quality of 

Service (QoS) Object (72 / 0x48) (

130)

)

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13840 | DLR Network Topology

Data type: UNSIGNED_8

Index: 10735 = 0x29EF

Display of the used DLR network topology (Device Level Ring)

(Instance attribute 1 (Network Topology) in the 

Device Level Ring (DLR) Object (71 / 0x47) (

128)

)

Selection list 

(read only)

0 Linear
1 Ring

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13841 | DLR Network Status

Data type: UNSIGNED_8

Index: 10734 = 0x29EE

Display of the DLR network status (Device Level Ring)

(Instance attribute 2 (Network Status) in the 

Device Level Ring (DLR) Object (71 / 0x47) (

128)

)

Selection list 

(read only)

0 Normal
1 Ring Fault
2 Unexpected Loop detected
3 Partial network fault
4 Rapid fault/restore cycle

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments