Lenze E94AYCEO Communications Manual Download Page 52

Page: 52 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

I/O data transfer (implicit messages)

8.1

Technology applications (TA) / drive profiles

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

8.1

Technology applications (TA) / drive profiles

The Servo Drive 9400 is provided with different drive profiles. They define a standardised or

individual control and status word assignment as well as the standardisation of setpoint and actual

value scalings.
The Servo Drive 9400 supports Lenze technology applications and user-definable parameter sets.

8.1.1

Lenze technology applications / user-definable parameter sets

The technology applications integrated in the drive provide the main signal flow for realising a

general or specific drive solution.
In order to use the Lenze technology applications, the following assembly object instances must be

used in the host (scanner):

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 52 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: