manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 143 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 143

14

Implemented CIP™ objects

14.3

Lenze objects

143

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

14.3.4

Lenze Class (110 / 0x6E)

The "Lenze Class (110 / 0x6E)" enables read or write access to Lenze codes.
The Lenze code must be specified as an "instance" (corresponding code no. 1 ... 65535) and its

subcodes must be specified as "attributes".

Class attributes

Instance attributes

Supported service codes

Note!

• If the corresponding Lenze code does not have a subcode, the value '0' must be 

entered in the attribute. If '0' is not supported as attribute value by the engineering 

tool used, the value '1' must be entered.

• A display code cannot be configured using "Set_Attribute_Single".

Attribute 

ID

Service

Name

Data type

Value

1

Get

Revision

UINT

2 (0x0002)

2

Get

Max. Instance

UINT

1 (0x0001)

Attribute 

ID

Service

Name

Data type

Value

0 ... 255

Get / Set Lenze Subcode number

Data type of 

the subcode

Value of the subcode

Service code

Name

Description

0x0E

Get_Attribute_Single

Outputs the value of a certain attribute.

0x10

Set_Attribute_Single

Changes the value of a certain attribute.

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments