Lenze E94AYCEO Communications Manual Download Page 62

Page: 62 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

I/O data transfer (implicit messages)

8.3

I/O configuration with »RSLogix 5000« version 19 or lower

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

9. Complete the settings with

• The I/O configuration is now complete.
• The corresponding tags are then created in the "controller tags" of the control project:

In the example, the drive was named "My_E94AYCEO". There are three tag sets labelled

"My_E94AYCEO":

• "My_E94AYCEO:C" for the assembly configuration instance "1"
• "My_E94AYCEO:I" for the assembly input object instance "111"
• "My_E94AYCEO:O" for the assembly output object instance "110"

Click on the

[ + ]

in front of the "My_E94AYCEO" data to display the I/O data words of the

assemblies.

10. The last step is

Saving the I/O configuration in »RSLogix 5000«

(



69)

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 62 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: