manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 12 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 12

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

12

2

Safety instructions

2.2

Device and application-specific safety instructions

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

2.2

Device and application-specific safety instructions

• During operation, the communication module must be securely connected to the standard 

device.

• With external voltage supply, always use a separate power supply unit, safely separated to 

EN 61800-5-1 in every control cabinet (SELV/PELV).

• Only use cables that comply with the listed specifications.

Ethernet cable specification

 (

30)

 

2.3

Residual hazards

Protection of persons

If Servo Drives 9400 are used on a phase earthed mains with a rated mains voltage of 

400 V, the

protection against accidental contact is not ensured without external measures.

Protective insulation

 (

19)

Device protection

The communication module contains electronic components which may be damaged or destroyed

by electrostatic discharge.

Installation

 (

23)

 

Documentation for the standard device, control system, system/machine

All the other measures prescribed in this documentation must also be implemented. 

Observe the safety instructions and application notes contained in this manual.

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments