Lenze E94AYCEO Communications Manual Download Page 19

Page: 19 / 149

Technical data

4.5

Protective insulation

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

4.5

Protective insulation



Danger!

Dangerous voltage

If the Servo Drives 9400 are operated on a phase earthed mains with a rated mains

voltage



400 V, external measures need to be implemented in order to ensure

protection against accidental contact.

Possible consequences:

Death or severe injuries

Protective measures:

If protection against accidental contact is required for the control terminals of the

inverter and the connections of the plugged device modules, ...

• a double isolating distance must exist.
• the components to be connected must be provided with the second isolating

distance.



Note!

The protective insulation provided in Servo Drives 9400 is implemented in accordance

with EN 61800-5-1.

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 19 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: