manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 134 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 134

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

134

14

Implemented CIP™ objects

14.2

EtherNet/IP objects

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

Instance attribute "Configuration Capability" (attribute 2)

6

AcdStatus

Display of the status of address conflict detection (ACD):

• 0: No address conflict detected

• 1: Address conflict detected

7 ... 31

-

Reserved (0)

Bits

Name

Description

0

BOOTP Client

The state ’1’ indicates that BOOTP is used for the TCP/IP configuration of 

the device.

1

DNS Client

Is not supported (state ’0’).

2

DHCP Client

The state ’1’ indicates that DHCP is used for the TCP/IP configuration of 

the device.

3

DHCP-DNS Update

Is not supported (state ’0’).

4

Configuration Settable

The state ’1’ indicates that the TCP/IP configuration can be set in 

attribute 5 (Interface Configuration).

5

Hardware Configurable

Is not supported (state ’0’).

6

Interface Configuration 

Change Requires Reset

The state ’1’ indicates that changes of the TCP/IP configuration in 

attribute 5 (Interface Configuration) will only take effect after a reset of 

the device ("power off/on" or "type 0 reset").

The state ’0’ is not supported (changes becoming effective immediately).

7

AcdCapable

The state ’1’ indicates that the device is provided with address conflict 

detection (ACD).

8 ... 31

-

Reserved (0)

Bits

Name

Description

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments