manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 55 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 55

8

I/O data transfer (implicit messages)

8.2

I/O configuration in the »Engineer«

55

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

8.2

I/O configuration in the »Engineer«

For the Servo Drives 9400 HighLine the I/O data can be arranged individually (mapping). For this

purpose, the »Engineer« is provided with a port configurator.

Below you can find a description of the steps required to realise an I/O data communication with

the host (scanner) in which one control/status word and one 32 bit setpoint/actual value are

exchanged each.

How to implement PDO mapping using the »Engineer«:

1. In the »Engineer«, the mapping of the I/O data is carried out under the 

Process data objects

 

tab of the respective fieldbus communication module:

2. Select the receive object 

PDO_RX0

:

Note!

The port mapping is no configuration that can be carried out online for the Servo Drive 

9400. For this purpose, an update of the »Engineer« project and a subsequent download 

of the application is always required.

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments