Lenze E94AYCEO Communications Manual Download Page 130

Page: 130 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

130

Implemented CIP™ objects

14.2

EtherNet/IP objects

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

14.2.2

Quality of Service (QoS) Object (72 / 0x48)

The "Quality of Service (QoS) Object" enables different classifications and prioritisations of the data

packets for EtherNet/IP communication. For this purpose, the EtherNet/IP messages are marked

with "802.1Q tags" and "Differentiated Services Codepoints" (DSCP).

Class attributes

Instance attributes

The instance attributes act independently of each other.
The DSCP values are used for the IP headers.
Irrespective of this,

VLAN tagging

can be activated additionally (

C13021

C14021

= 1).

The VLAN ID of Lenze devices is ’0’.
The VLAN priority results from the DSCP values configured.
Changes in the attribute values will only take effect after a reset of the device ("power off/on" or

"type 0 reset").

Attribute

Service

Name

Data type

Value

Get

Revision

UINT

1 (0x0001)

Get

Max. Instance

UINT

1 (0x0001)



Note!

Before activating VLAN tagging, please ensure that all involved components support

VLAN tagging. It may occur that the devices not supporting VLAN tagging cannot be

accessed anymore.

Attribute

Service

Name

Data type

Value

Set

802.1Q Tag Enable

USINT

Enables the transmission of data packets

with 802.1Q tags (

C13021

C14021

)

• 0: No use of 802.1Q tags (Lenze setting)

• 1: Use of 802.1Q tags

Set

DSCP Urgent

USINT

55: Urgent/imperative messages

Is not supported at the moment.

Set

DSCP Scheduled

USINT

47: Scheduled messages

(Can only be used for "exclusive owner"

connections.)

(

C13022/4

C14022/4

)

Set

DSCP High

USINT

43: Messages with high priority

(Can only be used for "input only" and "listen

only" connections.)

(

C13022/5

C14022/5

)

Set

DSCP Low

USINT

31: Messages with low priority

Is not supported at the moment.

Set

DSCP Explicit

USINT

27: "Explicit messages" (parameter data)

(

C13022/7

C14022/7

)

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 130 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: