Lenze E94AYCEO Communications Manual Download Page 37

Page: 37 / 149

Commissioning

6.3

Setting the IP configuration of the Servo Drive 9400

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.3

Setting the IP configuration of the Servo Drive 9400

The IP configuration is required for addressing the Servo Drive 9400 to ensure that communication

between the PC/»Engineer« or the scanner and the drive can be effected via EtherNet/IP. For this,

an IP address, subnet mask, and gateway address must be allocated. You have the following options

to select the IP parameters for the Servo Drive 9400:

•

Setting via the EtherNet/IP configurator of the »Engineer«

(



38)

•

Setting via codes in the »Engineer«

(



40)

•

Setting via a BOOTP/DHCP server

(



42)

•

Setting via the TCP/IP Interface Object (0xF5)

(



42)



Note!

• The assignment of invalid combinations of IP address, subnet mask, and gateway

address can have the consequence that no connection to the EtherNet/IP network can

be established.

• Codes

(IP address),

(subnet mask),

(gateway address), and

C13016

C14016

(multicast IP address) show the IP

parameters currently used.

• In the case of impermissible settings, the error message

EtherNet/IP: Invalid IP

parameters [0x00c86533]

(



84)

is output.

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 37 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: