Lenze E94AYCEO Communications Manual Download Page 42

Page: 42 / 149

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

Commissioning

6.3

Setting the IP configuration of the Servo Drive 9400

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

6.3.3

Setting via a BOOTP/DHCP server

DHCP is the acronym for "Dynamic Host Configuration Protocol". This protocol is defined in

RFC 2131 and is a compatible advancement of the "Bootstrap Protocol" (BOOTP) according to

RFC 951.
Both protocols enable network nodes to query information about the network configuration (e.g.

the IP address) from a server via a TCP/IP network. The BOOTP/DHCP server assigns the IP address

to the client dynamically from a defined address range. This means that the client receives an

unambiguous IP address.
Code

C13005

C14005

is used to define how the IP configuration is to be carried out:

• Value ’0’: The IP configuration currently saved in the communication module is used.
• Value ’1’: BOOTP is used. (Lenze standard setting)
• Value ’2’: DHCP is used.

This setting can also be made by means of write access to attribute 3 (Configuration Control) of

instance 1 of the

TCP/IP Interface Object (245 / 0xF5)

(



132)

6.3.4

Setting via the TCP/IP Interface Object (0xF5)

A scanner serves to set the IP configuration via attribute 5 (Interface configuration) of instance 1 of

the

TCP/IP Interface Object (245 / 0xF5)

(



132)

After the IP configuration, carry out a node reset ("power off/on" or "Type 0 reset" for the

In »Engineer«, codes

(IP address),

(subnet mask),

(gateway address), and

C13016

C14016

(multicast IP address) show the IP parameters

currently used.

Summary of Contents for E94AYCEO






















































































































































Search results

Summary of Contents for E94AYCEO

Reviews:

Lenze E94AYCEO, Communications Manual, Page: 42 / 149

Search results

Summary of Contents for E94AYCEO

Reviews: