manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 91 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 91

13

Parameter reference

13.2

Parameters of the communication module for slot MXI1

91

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

C13003

C13005

C13006

Parameter | Name:

C13003 | MAC ID

Data type: OCTET_STRING

Index: 11572 = 0x2D34

Display of the MAC-ID

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13005 | IP configuration reference

Data type: UNSIGNED_8

Index: 11570 = 0x2D32

Selection how the IP configuration is to be effected.

(Instance attribute 3 (Configuration Control) in the 

TCP/IP Interface Object (245 / 0xF5) (

132)

)

Setting the IP configuration of the Servo Drive 9400 (

37)

Selection list 

(Lenze setting printed in bold)

Info

0 Use stored IP

The IP configuration currently saved in the 

communication module is used.

1 Use  BOOTP

The IP configuration is assigned by the scanner using 

BOOTP.

2 Use DHCP

The IP configuration is assigned by the scanner using 

DHCP.

The assignment of a gateway address which is not in the 

same subnetwork than the IP address, is rejected.

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C13006 | Multicast IP Start Address

Data type: UNSIGNED_8

Index: 11569 = 0x2D31

Setting of the multicast IP address

Setting the IP configuration of the Servo Drive 9400 (

37)

Setting range 

(min. value | unit | max. value)

0

255

Subcodes

Lenze setting

Info

C13006/1

239

Multicast IP start address (most significant byte)

C13006/2

64

Multicast IP start address

C13006/3

2

Multicast IP start address

C13006/4

224

Multicast start address (least significant byte)

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments