manualshive.com logo in svg

Lenze E94AYCEO, Communications Manual, Page: 103 / 149

Share
Download
Lenze E94AYCEO Communications Manual Download Page 103

13

Parameter reference

13.3

Parameters of the communication module for slot MXI2

103

Lenze · E94AYCEO communication module (EtherNet/IP™) · Communication Manual · DMS 3.0 EN · 12/2013 · TD17

 

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 

13.3

Parameters of the communication module for slot MXI2

This chapter lists the parameters of the E94AYCEO communication module (EtherNet/IP) for slot

MXI2 of the Servo Drive 9400 in numerically ascending order.

C14000

C14001

C14002

Parameter | Name:

C14000 | IP address

Data type: UNSIGNED_8

Index: 10575 = 0x294F

Setting of the IP address

Setting the IP configuration of the Servo Drive 9400 (

37)

Setting range 

(min. value | unit | max. value)

0

255

Subcodes

Lenze setting

Info

C14000/1

192

IP address (most significant byte)

C14000/2

168

IP address

C14000/3

124

IP address

C14000/4

16

IP address (least significant byte)

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C14001 | Subnetwork mask

Data type: UNSIGNED_8

Index: 10574 = 0x294E

Setting of the subnet mask

Setting the IP configuration of the Servo Drive 9400 (

37)

Setting range 

(min. value | unit | max. value)

0

255

Subcodes

Lenze setting

Info

C14001/1

255

Subnet mask (most significant byte)

C14001/2

255

Subnet mask

C14001/3

255

Subnet mask

C14001/4

0

Subnet mask (least significant byte)

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Parameter | Name:

C14002 | Gateway address

Data type: UNSIGNED_8

Index: 10573 = 0x294D

Setting of the gateway address

Setting the IP configuration of the Servo Drive 9400 (

37)

Setting range 

(min. value | unit | max. value)

0

255

Subcodes

Lenze setting

Info

C14002/1

0

Gateway address (most significant byte)

C14002/2

0

Gateway address

C14002/3

0

Gateway address

C14002/4

0

Gateway address (least significant byte)

Read access

Write access

CINH

PLC STOP

No transfer

PDO_MAP_RX

PDO_MAP_TX

COM

MOT

Summary of Contents for E94AYCEO






















































































































































Reviews:

No comments