Lenovo ThinkSystem NE0152T Installation Manual Download Page 55

Page: 55 / 110

Chapter 4. Removing and Replacing Components

This chapter describes how to remove NE0152T hardware components for
replacement. The following topics are covered:



“Removing Port Transceivers” on page 56



Removing and replacing hot-swap modules



“Removing and Replacing a Power Supply Module” on page 57



“Removing and Replacing a Fan Module” on page 61



Removing the switch from one of the supported rack types



“Removing the NE0152T from a Standard Equipment Rack” on page 63



“Removing the NE0152T from a Lenovo System x or Power Rack” on page 64



“Removing the NE0152T from a Lenovo iDataPlex Rack” on page 67



“Removing the Air-Duct Option” on page 69



“Replacing the NE0152T” on page 70

Summary of Contents for ThinkSystem NE0152T















































































































Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands

Lenovo ThinkSystem NE0152T, Installation Manual

Search results

Summary of Contents for ThinkSystem NE0152T

Reviews:

Related manuals for ThinkSystem NE0152T

Brands by name

Popular brands